Skf Tih 100m Parts Manual
497-9584; Mfr. SKF induction coil Bearing Heaters designed to carefully and evenly heat bearings that are mounted. The TIH 100m has the same capabilities as the smaller heater but with increased capacity. Add to a parts list. SKF TIH 100M INSTRUCTIONS FOR USE MANUAL Pdf Download. - View and Download SKF TIH 100m instructions for use manual online. TIH 100m Electric Heater pdf manual download.
Bearing Induction Heater Avaialble in 230V version (RS and 110V version (RS) SKF induction coil Bearing Heaters designed to carefully and evenly heat bearings that are mounted with an interference fit onto a shaft. Bearing heaters allow bearings to be installed without the need for specific hand tools. They eliminate the need for force to be applied to the bearing during installation. Bearing heaters can be used to heat other engineering components, such as gears, pulleys, bushes, where the bearing heater-component being heated forms a closed electrical circuit. The induction coil is housed outside the heater housing, providing a shorter heating time and reduced energy consumption during use.
Foldable bearing support arms facilitate the heating of larger bearings/other suitable components, and a magnetic temperature probe helps prevent overheating. The heaters feature an integrated, easy-to-use control panel and handset/remote control.
An integrated carrying handle is built into the bearing heater design, and each heater comes complete with three yokes. Features and Benefits 2-step power setting and smaller yokes allow heating smaller bearings safely and at lower power consumption Temperature mode pre-set at 110°C to prevent over-heating Automatic demagnetisation Capable of heating a 28kg bearing in 20 min Compact lightweight design facilitating portability The TIH 100m has the same capabilities as the smaller heater but with increased capacity. The advanced design of the power electronics allows accurate electric current control. Technical Specification Voltage 230V, 50-60Hz Workpiece Max. Weight 40kg (88lb) Bore Range 20-300mm (0.8-11.8in.) Dimensions 450 x 195 x 210mm Total Weight (inc.
Yokes) 20.9kg (46lb) Max. Power Consumption 2.0kVA Standard Yokes Supplied 45 x 45 x 215mm 28 x 28 x 215mm 14 x 14 x 215mm Note No fitted electrical cable plug is supplied with the bearing heater. An approved electrical plug should be attached by a suitably-qualified individual to suit local requirements, such as: (UK) BS1363 rubber plug; (DE) Schuko rubber plug 8 or; (FR) rubber plug; or (US and JP) nylon plug.
SKF Electric Induction Heaters and Hot Plates enable bearings and other machinery components to be heated prior to installation. The induction heaters and hot plates are suitable for use with a variety of component sizes (actual sizes accepted depend on which induction heater or hot plate is used) and individual components may be heated to 200/250°C. SKF induction heaters and hot plates are thermostatically-controlled, and for safety reasons, overheat protection is also incorporated into the units to ensure that the induction heater or hot plate is switched off in the event of thermostat failure.
The SKF medium induction heater TIH 100m has the same high standards of efficiency and performance as the smaller heater, combined with increased capacity. The advanced design of the power electronics allows features of accurate electric current control, cut-outs to avoid overheating, controls on rate of temperature increase, these are as some of the standard features in the TIH.m range. Placing the induction coil outside the heater’s housing allows the heating of bearings weighing up to 120 kg (264 lb). The heater is equipped with thermal overheating protection to reduce the risk of damage to the induction coil and the electronics. In addition to temperature mode, the TIH 100m is equipped with a time mode for heating components other than bearings. The heater is supplied standard with three yokes and is available in two executions: 230V/50-60Hz or 400-460V/50-60Hz. Technical data Designation TIH 100m SKF m 20 performance 97 kg (213 lb) Voltage, V/Hz - TIH 100M/230V - TIH 100M/MV 230V/50-60Hz 400-460V/50-60Hz Bearing: - Maximum weight 120 kg (264 lb) - Maximum bore diameter 20 - 400 mm (0.8 - 15.7 in.) Temperature control: - Range.
Skf Tih 100m/230v
0 - 250 °C (32 - 482 °F) - Magnetic probe Yes, K-type - Accuracy (electronics) ± 2 °C (± 3,6 °F) Time control: - Range 0 - 60 minutes - Accuracy ± 0,01 sec. Application example: - bearing, weight, temperature, time 23156 CC/W33, 97 kg, 110 °C, 20m Thermometer mode Yes Bearing mode Yes Power reduction 2-step; 50 - 100% Demagnetisation according to SKF norms (automatic) Yes (.
